Over Speed Sensor – Over Speed Alarm using Magnetic Pickup Sensor

socialicon

This is an over-speed sensor module, that provides an audible warning and signals output when the speed of a machine is above a set point. The module can be used in applications such as Engines, Machines, Sports machines, and Fitness Equipment. The speed of the machine or engine can be detected using magnetic pickup sensors. The project can be used in many applications where an over-speed monitor is important. The board is based on the LM2907 chip that works as a frequency to voltage converter, interfacing a magnetic pickup as shown in the figure below. A typical magnetic pickup for automotive applications will provide a thousand pulses per mile so that at 60 mph the incoming frequency will be 16.6Hz. When the reference level on the comparator is set by two equal resistors R2 and R6 then the desired value of C5 and R4 can be determined from the following simple relationship:

The buzzer is energized when Frequency ≥ (1/(2XR4C5))

From the RC selection chart, we can choose suitable values for R5 and C5. With the current circuit, the frequency is set to 500Hz approx. The frequency trigger point can be changed as per user requirement using above equation. The module supports any sensor voltage level from 20mV to 28V.

If you are looking for “Under Speed Warning Alarm for Magnetic Pickup sensor” check the link attached.

RC selection Diagram

Magnetic Pickup Sensor

A Magnetic Pickup Sensor consists of a permanent magnet, a pole-piece, and a sensing coil all encapsulated in a cylindrical case. Magnetic Pickup is most frequently used to sense passing teeth on a gear, sprocket, or timing belt wheel, to bolt-heads, key-ways, or other moving machine-mounted targets.

Magnetic Pickup Sensor

Connections: CN1

  • Pin 1 Output Normally Low, Goes High When Over Speed Sense,
  • Pin 2, Pin5, Pin6 = GND
  • Pin 3 and Pin 4 = VCC Supply Input

Connections CN2: Magnetic Pick Up Sensor

Features

  • Supply 12 to 15V DC @ 20mA
  • Optimized for Magnetic Pickup Sensor
  • Other Optical Sensor, Mechanical Sensor, and Tachometer sensors can be used
  • Inputs Voltage Level 20mV to 28V
  • Buzzer Operates when the Input frequency is above 500Hz
  • Provide High Output When Speed is below Set Point
  • Header Connector for Supply Input and Output
  • 2 Pin Header for Sensor
  • D1 Power LED
  • PCB Dimensions 38.42 x 16.19mm

Applications

  • Engines
  • Tachometer Under/Over Speed
  • Fitness Equipment
  • Sports Machines
  • Machine Automation
  • AC/DC Motor Speed Monitor

Schematic



Parts List

NOQNTY.REF.DESC.MANUFACTURERSUPPLIERPART NO
11BZ1BUZZERCUI DEVICEDIGIKEY102-CMI-1295-1285T-ND
21CN16 PIN MALE HEADER PITCH 2.54MMWURTHDIGIKEY732-5319-ND
31CN22 PIN MALE HEADER PITCH 2.54MMWURTHDIGIKEY732-5315-ND
41C110uF/25V SMD SIZE 1206YAGEO/MURATADIGIKEY
51C20.1uF/50V SMD SIZE 0805YAGEO/MURATADIGIKEY
61C31uF/25V SMD SIZE 1206YAGEO/MURATADIGIKEY
73C4,R8,R9DNP
81C50.01uF/50V SMD SIZE 1206YAGEO/MURATADIGIKEY
91D1LED SMD SIZE 0805LITE ON INCDIGIKEY160-1427-1-ND
101Q1BC847ALMICRO COMMERCIALDIGIKEYBC847B-TPCT-ND
112R1,R71K 5% SMD SIZE 0805YAGEO/MURATADIGIKEY
123R2,R5,R65K1 1% SMD SIZE 0895YAGEO/MURATADIGIKEY
131R3100E 5% SMD SIZE 0805YAGEO/MURATADIGIKEY
141R4100K 1% SMD SIZE 0805YAGEO/MURATADIGIKEY
151U1LM2907-NTIDIGIKEYLM2907M-8/NOPB-ND

Connections

Magnetic Pickup Sensor

Gerber View

Photos

Video

LM2907 Datasheet

Please follow and like us:
Pin Share

PCB

Subscribe
Notify of
guest

0 Comments
Inline Feedbacks
View all comments

RELATED PROJECTS